Strut Services Group, Inc.

Unistrut Alabama

P1000

$

P1000 – 1-5/8″ x 1-5/8″, 12 Gage Channel, Solid

12 Gauge Solid Strut Channel

Unistrut’s P1000 is the original metal framing strut channel and has been used in countless applications for over 90 years. Commonly known as 12 Gauge Standard or Deep Strut Channel, it is the global standard for strut metal framing.

This channel is commonly used for trapeze supports, seismic bracing, ceiling grids, pipe, conduit, duct and cable tray supports, racks, and other general framing. For application examples, refer to our Application Showcase.

The P1000 is OPA approved for seismic bracing and will be included in our upcoming OPM. It is also UL Listed and CSA Listed for use as a Strut-Type Channel Raceway.

Product dimensions are 1 5/8″ wide x 1 5/8″ tall x 12 ga. thick, solid. Punched holes are also available for ease of installation.

Our P1000 is available in Pre-Galvanized (PG), Unistrut Defender (DF), Hot-Dip Galvanized (HG), Plain (PL), Green (GR), Zinc Dichromate (ZD), Stainless Steel (SS or ST) and Aluminum (EA).

 

Part No. Length (ft) Finish Product Weight / Ft (lbs/ft)
P1000 20 PG 1.89
P1000 10 PG 1.89
P1000 20 DF 2.014
P1000 10 DF 2.014
P1000 20 HG 2.014
P1000 10 HG 2.014
P1000 10 GR 1.89
P1000 20 GR 1.89
P1000 20 PL 1.89
P1000 10 PL 1.89
P1000 10 ZD 1.89
P1000 20 ZD 1.89
P1000 10 SS 1.89
P1000 20 SS 1.89
P1000 20 ST 1.89
P1000 10 ST 1.89
P1000 20 EA 0.733
P1000 10 EA 0.733
Beam Loading – P1000

Span
(in)

Max
Allow.
Uniform
Load(lbs)

Deflection at
Uniform Load(in)

Uniform Loading
at Deflection

Lateral Bracing
Reduction Factor

Span/180
(lbs)

Span/240
(lbs)

Span/360
(lbs)
24 1,690 0.06 1,690 1,690 1,690 1.00
36 1,130 0.13 1,130 1,130 900 0.94
48 850 0.22 850 760 500 0.88
60 680 0.35 650 480 320 0.82
72 560 0.5 450 340 220 0.78
84 480 0.68 330 250 160 0.75
96 420 0.89 250 190 130 0.71
108 380 1.14 200 150 100 0.69
120 340 1.40 160 120 80 0.66
144 280 2.00 110 80 60 0.61
168 240 2.72 80 60 40 0.55
192 210 3.55 60 50 NR 0.51
216 190 4.58 50 40 NR 0.47
240 170 5.62 40 NR NR 0.44
Note NR – Not Recommended
Column Loading – P1000
Column Loading – P1000

Unbraced
Height(in)

Allowable
Load atSlot Face(lbs)
Max Column Load

Applied at C.G.

K=0.65 (lbs) K=0.80 (lbs) K=1.0 (lbs) K=1.2 (lbs)
24 3,550 10,740 9,890 8,770 7,740
36 3,190 8,910 7,740 6,390 5,310
48 2,770 7,260 6,010 4,690 3,800
60 2,380 5,910 4,690 3,630 2,960
72 2,080 4,840 3,800 2,960 2,400
84 1,860 4,040 3,200 2,480 1,980
96 1,670 3,480 2,750 2,110 1,660
108 1,510 3,050 2,400 1,810 KL/r>200
120 1,380 2,700 2,110 KL/r>200 KL/r>200
144 1,150 2,180 1,660 KL/r>200 KL/r>200
Elements of Section – P1000
Area of Section 0.555 in2 (3.6 cm2)
Axis 1-1 Axix 2-2
Moment of Inertia (I) 0.185 in4 (7.7 cm4) 0.236 in4 (9.8 cm4)
Section Modulus (S) 0.202 in3 (3.3 cm3) 0.290 in3 (4.8 cm3)
Radius of Gyration (r) 0.577 in (1.5 cm) 0.651 in (1.7 cm)
Standard Lengths:
  • 10 feet: 10′ or 10’ 1/8” (3.05m) ± 1/8″ (3 mm)
  • 20 feet: 20′ or 20’ 3/8” (6.11m) ± 1/8″ (3 mm)
Special Lengths:
  • Available with a tolerance of ±1/8″ (3 mm). Request quote.
Curved Channel:
  • Many Unistrut channel sections can be supplied with a curve. Contact us for our ordering form, specifications, and instructions.
Load Data:
  • All beam and column load data pertains to carbon steel and stainless steel channels.
  • Load tables apply only to UNISTRUT brand channel. Look for “UNISTRUT” on the product.
  • Load tables and charts are constructed to be in accordance with the SPECIFICATION FOR THE DESIGN OF COLD-FORMED STEEL STRUCTURAL MEMBERS 2007 EDITION published by the AMERICAN IRON AND STEEL INSTITUTE USING ASD METHOD.
  • Loads are based on 33 ksi steel cold formed to 42 ksi.
  • Safety Factor to Yield Strength is 1.67 for Beam Loads and 1.80 for Column Loads.
  • Beam loads are based on a simple beam and are given as a total uniform load (W) in pounds. For proper calculation procedures, refer to our Beam Load Calculation Guide.
  • For bearing loads, reference our bearing loads page.
Welds:
  • Welded channels are spot welded 2″ (51 mm) or 3″ (76 mm) on-center.

Materials & Finishes – Standard:

  • Pregalvanized (PG):  Conforms to ASTM A653 SS GR 33, G90.
  • Unistrut Defender (DF):  Conforms to ASTM A1046 SS GR 33
  • Hot Dip Galvanized (HG):  Steel conforms to ASTM A1011 SS GR 33, Finish conforms to ASTM A123
  • Perma-Green (GR):  Steel conforms to ASTM A1011 SS GR 33, E-Coat finish
  • Perma-Gold (ZD):  Steel conforms to ASTM A1011 SS GR 33, Finish conforms to ASTM B633, Type II SC3
  • Plain (PL):  Conforms to ASTM A1011 SS GR 33

Materials & Finishes – Special Metals:

  • Stainless Steel, Type 304 (SS):  ASTM A240, Type 304 *
  • Stainless Steel, Type 316 (ST):  ASTM A240, Type 316 *
  • Aluminum (EA):  ASTM B221, Type 6063-T6 (Extruded) *

* These materials have different physical properties and performance characteristics. Please contact us for design support.

Scroll to Top