Strut Services Group, Inc.

Unistrut Alabama

P1001WT

$

P1001WT – 1-5/8″ x 3-1/4″, 12 Gage, Back-to-Back, Slotted

Unistrut’s P1001WT (back-to-back slotted) has slots on the back side for use with 5/8″ threaded rod and fasteners. The wider slots are an advantage during installation, eliminating the need for field drilling traditional slotted channel while retaining the adjustability of traditional slotted channel.

This channel is commonly used for trapeze supports, anchoring to concrete, ceiling grids, pipe, conduit, duct and cable tray supports, racks, and other general framing.

Product dimensions are 1 5/8″ wide x 3 1/4″ tall x 12 ga. thick; back-to-back with slots. The slots are 2″ wide x 11/16″ long, 3″ on center and sized for use with 5/8″ threaded rod or fasteners.

Our P1001WT is available in the following finishes: Pre-Galvanized (PG), Hot-Dip Galvanized (HG), Plain (PL), Green (GR), Zinc Dichromate (ZD) and Stainless Steel (SS).

 

Part No. Length (ft) Finish Product Weight / Ft (lbs/ft)
P1001WT 10 PG 3.78
P1001WT 20 PG 3.78
P1001WT 10 HG 3.92
P1001WT 20 HG 3.92
P1001WT 20 GR 3.78
P1001WT 10 GR 3.78
P1001WT 20 PL 3.78
P1001WT 10 PL 3.78
P1001WT 20 ZD 3.78
<!–

–>

Beam Loading – P1001WT
Beam Loading – P1001WT

Span

(in)


Max
Allowable Uniform
Load

(lbs)


Deflection at Uniform Load

(in)


Uniform Loading
at Deflection

Lateral Bracing Reduction Factor

Span/180

(lbs)


Span/240

(lbs)


Span/360

(lbs)

24 * 3,500 0.02 * 3,500 * 3,500 * 3,500 1.00
36 2,712 0.07 2,712 2,712 2,712 1.00
48 2,032 0.13 2,032 2,032 2,032 1.00
60 1,624 0.20 1,624 1,624 1,377 0.97
72 1,360 0.28 1,360 1,360 961 0.93
84 1,165 0.39 1,165 1,054 706 0.89
96 1,020 0.51 1,020 808 536 0.85
108 901 0.64 850 638 425 0.81
120 816 0.79 689 519 349 0.78
144 680 1.14 476 357 238 0.70
168 578 1.53 349 264 179 0.63
192 510 2.02 272 204 136 0.56
216 451 2.54 213 162 111 0.49
240 408 3.16 170 128 85 0.44
Note *Load limited by weld shear
<!–

–>

Column Loading – P1001WT
Column Loading – P1001WT

Unbraced Height

(in)


Allowable Load at Slot Face

(lbs)

Max Column Load
Applied at C.G.

K=0.65 (lbs) K=0.80 (lbs) K=1.0 (lbs) K=1.2 (lbs)
24 6,430 24,280 23,610 22,700 21,820
36 6,290 22,810 21,820 20,650 19,670
48 6,160 21,410 20,300 18,670 16,160
60 6,000 20,210 18,670 15,520 12,390
72 5,620 18,970 16,160 12,390 8,950
84 5,170 16,950 13,630 9,470 6,580
96 4,690 14,890 11,190 7,250 5,040
108 4,170 12,850 8,950 5,730 3,980
120 3,690 10,900 7,250 4,640 KL/r>200
144 2,930 7,630 5,040 KL/r>200 KL/r>200
Elements of Section – P1001WT
Area of Section 1.111 in2 (7.2 cm2)
Axis 1-1 Axix 2-2
Moment of Inertia (I) 0.928 in4 (38.6 cm4) 0.471 in4 (19.6 cm4)
Section Modulus (S) 0.571 in3 (9.4 cm3) 0.580 in3 (9.5 cm3)
Radius of Gyration (r) 0.914 in (2.3 cm) 0.651 in (1.7 cm)
Standard Lengths:
  • 10 feet: 10′ or 10’ 1/8” (3.05m) ± 1/8″ (3 mm)
  • 20 feet: 20′ or 20’ 3/8” (6.11m) ± 1/8″ (3 mm)
Special Lengths:
  • Available with a tolerance of ±1/8″ (3 mm). Request quote.
Curved Channel:
  • Many Unistrut channel sections can be supplied with a curve. Contact us for our ordering form, specifications, and instructions.
Load Data:
  • All beam and column load data pertains to carbon steel and stainless steel channels.
  • Load tables apply only to UNISTRUT brand channel. Look for “UNISTRUT” on the product.
  • Load tables and charts are constructed to be in accordance with the SPECIFICATION FOR THE DESIGN OF COLD-FORMED STEEL STRUCTURAL MEMBERS 2007 EDITION published by the AMERICAN IRON AND STEEL INSTITUTE USING ASD METHOD.
  • Loads are based on 33 ksi steel cold formed to 42 ksi.
  • Safety Factor to Yield Strength is 1.67 for Beam Loads and 1.80 for Column Loads.
  • Beam loads are based on a simple beam and are given as a total uniform load (W) in pounds. For proper calculation procedures, refer to our Beam Load Calculation Guide.
  • For bearing loads, reference our bearing loads page.
Welds:
  • Welded channels are spot welded 2″ (51 mm) or 3″ (76 mm) on-center.

Materials & Finishes – Standard:

  • Pregalvanized (PG):  Conforms to ASTM A653 SS GR 33, G90.
  • Unistrut Defender (DF):  Conforms to ASTM A1046 SS GR 33
  • Hot Dip Galvanized (HG):  Steel conforms to ASTM A1011 SS GR 33, Finish conforms to ASTM A123
  • Perma-Green (GR):  Steel conforms to ASTM A1011 SS GR 33, E-Coat finish
  • Perma-Gold (ZD):  Steel conforms to ASTM A1011 SS GR 33, Finish conforms to ASTM B633, Type II SC3
  • Plain (PL):  Conforms to ASTM A1011 SS GR 33

Materials & Finishes – Special Metals:

  • Stainless Steel, Type 304 (SS):  ASTM A240, Type 304 *
  • Stainless Steel, Type 316 (ST):  ASTM A240, Type 316 *
  • Aluminum (EA):  ASTM B221, Type 6063-T6 (Extruded) *

* These materials have different physical properties and performance characteristics. Please contact us for design support.

Scroll to Top