Strut Services Group, Inc.

Unistrut Alabama

P1186, P2105-P2110

SKU P1186/P2105-P2110 Categories , ,
$

P1186 / P2105 / P2106 / P2107 / P2108 / P2109 / P2110 
Inside Angle Fitting (1-5/8″ Series)

Part No. A B Finish Product Weight / Piece (lbs)
P1186 45° 3-1/8″ (79) EG 0.58
P1186 45° 3-1/8″ (79) DF 0.615
P1186 45° 3-1/8″ (79) HG 0.615
P1186 45° 3-1/8″ (79) GR 0.58
P1186 45° 3-1/8″ (79) ZD 0.58
P1186 45° 3-1/8″ (79) SS 0.58
P2105 82-1/2° 3-3/16″ (81) EG 0.58
P2105 82-1/2° 3-3/16″ (81) HG 0.615
P2105 82-1/2° 3-3/16″ (81) GR 0.58
P2105 82-1/2° 3-3/16″ (81) ZD 0.58
P2106 75° 3-3/16″ (81) EG 0.58
P2106 75° 3-3/16″ (81) HG 0.615
P2106 75° 3-3/16″ (81) GR 0.58
P2106 75° 3-3/16″ (81) ZD 0.58
P2107 67-1/2° 3-1/8″ (79) EG 0.58
P2107 67-1/2° 3-1/8″ (79) HG 0.615
P2107 67-1/2° 3-1/8″ (79) GR 0.58
P2107 67-1/2° 3-1/8″ (79) PL 0.58
P2107 67-1/2° 3-1/8″ (79) ZD 0.58
P2108 60° 3-1/8″ (79) EG 0.58
P2108 60° 3-1/8″ (79) HG 0.615
P2108 60° 3-1/8″ (79) GR 0.58
P2108 60° 3-1/8″ (79) ZD 0.58
P2108 60° 3-1/8″ (79) SS 0.58
P2109 52-1/2° 3-1/16″ (78) EG 0.58
P2109 52-1/2° 3-1/16″ (78) HG 0.615
P2109 52-1/2° 3-1/16″ (78) GR 0.58
P2109 52-1/2° 3-1/16″ (78) ZD 0.58
P2110 37-1/2° 3″ (76) EG 0.58
P2110 37-1/2° 3″ (76) HG 0.615
P2110 37-1/2° 3″ (76) GR 0.58
P2110 37-1/2° 3″ (76) ZD 0.58
P2110 37-1/2° 3″ (76) SS 0.58

Standard Dimensions (Unless Shown Otherwise on Drawing):

  • Hole Diameter: 9/16″ (14mm)
  • Hole Spacing (From End): 13/16″ (21mm)
  • Hole Spacing (On-Center): 1 7/8″ (48mm)
  • Width: 1 5/8″ (41mm)
  •  Thickness:
    • 1/4″ (6.4mm) with steel meeting or exceeding ASTM A1011 SS GR 33, or
    • 0.220″ (5.6mm) with steel meeting or exceeding ASTM A1011 HSLAS GR 45

Note:

When used for mechanical supports, load capacities of brackets and fittings should be in compliance with the American Standard Code for Pressure Piping.

Materials & Finishes – Standard:

  • Base Metal: Steel conforms to ASTM A1011 SS GR 33, A1011 HSLAS GR 45, A36, A575, A576, or A635.
  • Electrogalvanized (EG):  Conforms to ASTM B633, Type III SC1
  • Unistrut Defender (DF):  Conforms to ASTM A1059
  • Hot Dip Galvanized (HG):  Conforms to ASTM A123 or A153
  • Perma-Green (GR):  Conforms to commercial standards for powder coating
  • Perma-Gold (ZD):  Conforms to ASTM B633, Type II SC1 or SC3
  • Plain (PL):  No finish

Materials & Finishes – Special Metals:

  • Stainless Steel, Type 304 (SS):  Conforms to ASTM A240 or A276, Type 304 *
  • Stainless Steel, Type 316 (ST):  Conforms to ASTM A240 or A276, Type 316 *
  • Aluminum (AL):  Conforms to ASTM B209, Type 1100F or 5052-H32 *

* These materials have different physical properties and performance characteristics. Please contact us for design support.

Design Loads – P1186, P2105 thru P2110
Part Number Angle  Average Ultimate Tension
(lbs)
 Design Tension Load
(lbs)
Average Deflection at Design Tension Load
P2105 82-1/2° 5,800 1,500 0.140″
P2106 75° 6,000 1,500 0.147″
P2107 67-1/2° 6,000 1,500 0.179″
P2108 60° 5,300 1,500 0.189″
P2109 52-1/2° 5,100 1,500 0.200″
P1186 45° 4,300 1,400 0.190″
P2110 37-1/2° 3,300 1,100 0.158″

Notes:

Design loads only apply to UNISTRUT brand products. Look for “UNISTRUT” on the part.
Design loads are based on static testing with a Safety Factor = 3.5, except for **, based on ultimate strength of connection. **Safety Factor – 3.0.
1/2″ Unistrut Channel Nut and Cap Screw torqued to 50 ft-lbs required for installation.
Design loads limited to 1,500 lbs for Slip Load of Channel Nuts.
Deflection measured in direction of tension load.

Scroll to Top