Strut Services Group, Inc.

Unistrut Alabama

P1386

SKU P1386 Categories ,
$

P1386 – Beam Clamp

Part No. Finish Product Weight / Piece (lbs)
P1386 EG 0.27
P1386 DF 0.286
P1386 HG 0.286
P1386 GR 0.27
P1386 SS 0.27

Standard Dimensions (Unless Shown Otherwise on Drawing):

  • Hole Diameter:  9/16”  (14mm)
  • Hole Spacing (From End):  13/16”  (21mm)
  • Hole Spacing (On-Center):  1 7/8”  (48mm)
  • Width:  1 5/8”  (41mm)
  • Thickness:
  • 1/4”  (6.4mm) with steel meeting or exceeding ASTM A1011 SS GR 33, or
  • 0.220″ (5.6mm) with steel meeting or exceeding ASTM A1011 HSLAS GR 45

Note:

When used for mechanical supports, load capacities of brackets and fittings should be in compliance with the American Standard Code for Pressure Piping.

Materials & Finishes – Standard:

  • Base Metal: Steel conforms to ASTM A1011 SS GR 33, A1011 HSLAS GR 45, A36, A575, A576, or A635.
  • Electrogalvanized (EG):  Conforms to ASTM B633, Type III SC1
  • Unistrut Defender (DF):  Conforms to ASTM A1059
  • Hot Dip Galvanized (HG):  Conforms to ASTM A123 or A153
  • Perma-Green (GR):  Conforms to commercial standards for powder coating
  • Perma-Gold (ZD):  Conforms to ASTM B633, Type II SC1 or SC3
  • Plain (PL):  No finish

Materials & Finishes – Special Metals:

  • Stainless Steel, Type 304 (SS):  Conforms to ASTM A240 or A276, Type 304 *
  • Stainless Steel, Type 316 (ST):  Conforms to ASTM A240 or A276, Type 316 *
  • Aluminum (AL):  Conforms to ASTM B209, Type 1100F or 5052-H32 *

* These materials have different physical properties and performance characteristics. Please contact us for design support.

Design Loads – P1386
ChannelStyle Design Load Each
(Use in Piars Only)
lbs (kN)
P1000 600  (2.67)
P1100 500  (2.22)
P2000 450  (2.00)

Notes:

Design loads only apply to Unistrut brand products. Look for “UNISTRUT” on the part.

Use in pairs only.

Safety factor = 5 based on ultimate strength of connection.

Requires a P1010 Channel Nut and 1/2″ bolt.

Set Screw Installation Torque: 125 in-lbs (14 N-m)

 

P1386 Allowable (Design) Loads
(lbs)
Pullout Slip Along Slip Thru
1,200 200 600

Notes:

Design loads only apply to UNISTRUT brand products. Look for “UNISTRUT” on the part.

Seismic design loads are for the 2 clamp installation as shown above. Must use clamps in pairs.

Design loads are based on static testing with a safety factor = 5 based on ultimate strength of connection.

Design loads apply only when used with 12ga. UNISTRUT channel.

A 1/2″ Chanel Nut and Bolt are required for installation.

Set Screw Installation Torque: 125 in-lbs (14 N-m)

Scroll to Top