Strut Services Group, Inc.

Unistrut Alabama

P3000WT

$

P3000WT – 1-5/8″ x 1-3/8″, 12 Gage, Slotted

Unistrut’s P3000WT has wide slots on the back side for use with 5/8″ threaded rod and fasteners. The wider slots are an advantage during installation, eliminating the need for field drilling traditional slotted channel while retaining the adjustability of traditional slotted channel.

This channel is commonly used for trapeze supports, anchoring to concrete, ceiling grids, pipe, conduit, duct and cable tray supports, racks, and other general framing. For application examples, refer to our Application Showcase. It has 85% of the capacity of the solid version of the profile.

Product dimensions are 1 5/8″ wide x 1 3/8″ tall x 12 ga. thick; with wide slots. The slots are 11/16″ wide x 2″ long, 3″ on center and sized for use with 5/8″ threaded rod or fasteners.

Our P3000WT is available in the following finishes: Pre-Galvanized (PG), Hot-Dip Galvanized (HG), Plain (PL), Green (GR), Zinc Dichromate (ZD), Aluminum (EA), and Stainless Steel (SS & ST).

 

Part No. Length (ft) Finish Product Weight / Ft (lbs/ft)
P3000WT 10 PG 1.65
P3000WT 20 PG 1.65
P3000WT 20 HG 1.74
P3000WT 10 HG 1.74
P3000WT 10 GR 1.65
P3000WT 20 GR 1.65
P3000WT 10 PL 1.65
P3000WT 20 PL 1.65
P3000WT 10 ZD 1.65
P3000WT 20 ZD 1.65
P3000WT SS 1.65
<!–

–>

Beam Loading – P3000WT
Beam Loading – P3000WT

Span

(in)


Max Allow. Uniform Load

(lbs)


Deflection at Uniform Load

(in)


Uniform Loading
at Deflection

Lateral Bracing Reduction Factor

Span/180

(lbs)


Span/240

(lbs)


Span/360

(lbs)

24 1,088 0.07 1,088 1,088 1,088 1.00
36 723 0.15 723 723 493 0.96
48 544 0.26 544 417 281 0.91
60 434 0.41 357 264 179 0.88
72 366 0.59 247 187 128 0.84
84 315 0.81 179 136 94 0.82
96 272 1.05 136 102 68 0.79
108 238 1.30 111 85 51 0.77
120 221 1.66 85 68 43 0.75
144 179 2.32 60 43 34 0.70
168 153 3.15 43 34 26 0.66
192 136 4.18 34 26 NR 0.62
216 119 5.21 NR NR NR 0.58
240 111 6.64 NR NR NR 0.54
Note NR – Not Recommended
<!–

–>

Column Loading – P3000WT
Column Loading – P3000WT

Unbraced

Height

(in)


Allowable Load at Slot Face

(lbs)

Max Column Load
Applied at C.G.
K=0.65 (lbs) K=0.80 (lbs) K=1.0 (lbs) K=1.2 (lbs)
24 3,180 9,690 8,980 8,050 7,210
36 2,920 8,160 7,210 6,130 5,240
48 2,590 6,820 5,810 4,730 3,860
60 2,300 5,740 4,730 3,690 2,990
72 2,040 4,850 3,860 2,990 2,270
84 1,830 4,100 3,240 2,400 KL/r>200
96 1,650 3,530 2,770 1,840 KL/r>200
108 1,450 3,080 2,270 KL/r>200 KL/r>200
120 1,250 2,710 1,840 KL/r>200 KL/r>200
Elements of Section – P3000WT
Area of Section 0.500 in2 (3.2 cm2)
Axis 1-1 Axix 2-2
Moment of Inertia (I) 0.120 in4 (5 cm4) 0.203 in4 (8.4 cm4)
Section Modulus (S) 0.153 in3 (2.5 cm3) 0.250 in3 (4.1 cm3)
Radius of Gyration (r) 0.489 in (1.2 cm) 0.638 in (1.6 cm)
Standard Lengths:
  • 10 feet: 10′ or 10’ 1/8” (3.05m) ± 1/8″ (3 mm)
  • 20 feet: 20′ or 20’ 3/8” (6.11m) ± 1/8″ (3 mm)
Special Lengths:
  • Available with a tolerance of ±1/8″ (3 mm). Request quote.
Curved Channel:
  • Many Unistrut channel sections can be supplied with a curve. Contact us for our ordering form, specifications, and instructions.
Load Data:
  • All beam and column load data pertains to carbon steel and stainless steel channels.
  • Load tables apply only to UNISTRUT brand channel. Look for “UNISTRUT” on the product.
  • Load tables and charts are constructed to be in accordance with the SPECIFICATION FOR THE DESIGN OF COLD-FORMED STEEL STRUCTURAL MEMBERS 2007 EDITION published by the AMERICAN IRON AND STEEL INSTITUTE USING ASD METHOD.
  • Loads are based on 33 ksi steel cold formed to 42 ksi.
  • Safety Factor to Yield Strength is 1.67 for Beam Loads and 1.80 for Column Loads.
  • Beam loads are based on a simple beam and are given as a total uniform load (W) in pounds. For proper calculation procedures, refer to our Beam Load Calculation Guide.
  • For bearing loads, reference our bearing loads page.
Welds:
  • Welded channels are spot welded 2″ (51 mm) or 3″ (76 mm) on-center.

Materials & Finishes – Standard:

  • Pregalvanized (PG):  Conforms to ASTM A653 SS GR 33, G90.
  • Unistrut Defender (DF):  Conforms to ASTM A1046 SS GR 33
  • Hot Dip Galvanized (HG):  Steel conforms to ASTM A1011 SS GR 33, Finish conforms to ASTM A123
  • Perma-Green (GR):  Steel conforms to ASTM A1011 SS GR 33, E-Coat finish
  • Perma-Gold (ZD):  Steel conforms to ASTM A1011 SS GR 33, Finish conforms to ASTM B633, Type II SC3
  • Plain (PL):  Conforms to ASTM A1011 SS GR 33

Materials & Finishes – Special Metals:

  • Stainless Steel, Type 304 (SS):  ASTM A240, Type 304 *
  • Stainless Steel, Type 316 (ST):  ASTM A240, Type 316 *
  • Aluminum (EA):  ASTM B221, Type 6063-T6 (Extruded) *

* These materials have different physical properties and performance characteristics. Please contact us for design support.

Scroll to Top