Strut Services Group, Inc.

Unistrut Alabama

P4000HS

$

P4000HS – 1-5/8″ x 13/16″, 16 Gage, Round Holes

Unistrut’s P4000HS has round holes on the back side for use with 1/2″ threaded rod and fasteners (or smaller diameters with use of flat washers). These holes can eliminate the need for field drilling when installing a trapeze support, anchoring the channel to a surface, or for many other applications.

This channel is commonly used for trapeze supports, seismic bracing, and anchoring to floors, ceilings and walls. This is a great product for certain seismic bracing applications where slots are not allowed.

Product dimensions are 1 5/8″ wide x 13/16″ tall x 16 ga. thick; with round holes on one side. The holes are 9/16″ in diameter and 1 7/8″ on center. The hole diameters and spacing match Unistrut’s general fittings so that nearly all our fittings can be attached and easily adjusted.

Our P4000HS is available in the following finishes: Pre-Galvanized (PG), Hot-Dip Galvanized (HG), Plain (PL), Green (GR), Zinc Dichromate (ZD), Stainless Steel (SS) and Aluminum (EA).

 

Part No. Length (ft) Finish Product Weight / Ft (lbs/ft)
P4000HS 20 PG 0.79
P4000HS 10 PG 0.79
P4000HS 20 HG 0.837
P4000HS 10 HG 0.837
P4000HS 10 GR 0.79
P4000HS 20 GR 0.79
P4000HS 20 PL 0.79
P4000HS 10 PL 0.79
P4000HS 10 ZD 0.79
P4000HS 20 ZD 0.79
P4000HS SS 0.79
P4000HS 20 EA 0.41
P4000HS 10 EA 0.41
<!–

–>

Beam Loading – P4000HS
Beam Loading – P4000HS

Span

(in)


Max Allow. Uniform Load

(lbs)


Deflection at Uniform Load

(in)


Uniform Loading
at Deflection

Lateral Bracing Reduction Factor

Span/180

(lbs)


Span/240

(lbs)


Span/360

(lbs)

24 369 0.11 369 333 225 1.00
36 243 0.24 198 153 99 0.94
48 180 0.43 108 81 54 0.88
60 144 0.67 72 54 36 0.83
72 126 1.01 54 36 27 0.79
84 108 1.38 36 27 18 0.75
96 90 1.72 27 18 18 0.72
108 81 2.20 18 18 9 0.69
120 72 2.68 18 9 9 0.66
<!–

–>

Column Loading – P4000HS
Column Loading – P4000HS

Unbraced

Height

(in)


Allowable

Load at Slot Face

(lbs)

Max Column Load
Applied at C.G.

K=0.65 (lbs) K=0.80 (lbs) K=1.0 (lbs) K=1.2 (lbs)
24 1,630 4,670 4,290 3,780 3,310
36 1,450 3,840 3,310 2,460 1,730
48 1,160 3,030 2,190 1,400 970
60 870 2,120 1,400 900 KL/r>200
72 670 1,470 970 KL/r>200 KL/r>200
Elements of Section – P4000HS
Area of Section 0.244 in2 (1.6 cm2)
Axis 1-1 Axix 2-2
Moment of Inertia (I) 0.023 in4 (1 cm4) 0.092 in4 (3.8 cm4)
Section Modulus (S) 0.049 in3 (0.8 cm3) 0.113 in3 (1.9 cm3)
Radius of Gyration (r) 0.306 in (0.8 cm) 0.613 in (1.6 cm)
Standard Lengths:
  • 10 feet: 10′ or 10’ 1/8” (3.05m) ± 1/8″ (3 mm)
  • 20 feet: 20′ or 20’ 3/8” (6.11m) ± 1/8″ (3 mm)
Special Lengths:
  • Available with a tolerance of ±1/8″ (3 mm). Request quote.
Curved Channel:
  • Many Unistrut channel sections can be supplied with a curve. Contact us for our ordering form, specifications, and instructions.
Load Data:
  • All beam and column load data pertains to carbon steel and stainless steel channels.
  • Load tables apply only to UNISTRUT brand channel. Look for “UNISTRUT” on the product.
  • Load tables and charts are constructed to be in accordance with the SPECIFICATION FOR THE DESIGN OF COLD-FORMED STEEL STRUCTURAL MEMBERS 2007 EDITION published by the AMERICAN IRON AND STEEL INSTITUTE USING ASD METHOD.
  • Loads are based on 33 ksi steel cold formed to 42 ksi.
  • Safety Factor to Yield Strength is 1.67 for Beam Loads and 1.80 for Column Loads.
  • Beam loads are based on a simple beam and are given as a total uniform load (W) in pounds. For proper calculation procedures, refer to our Beam Load Calculation Guide.
  • For bearing loads, reference our bearing loads page.
Welds:
  • Welded channels are spot welded 2″ (51 mm) or 3″ (76 mm) on-center.

Materials & Finishes – Standard:

  • Pregalvanized (PG):  Conforms to ASTM A653 SS GR 33, G90.
  • Unistrut Defender (DF):  Conforms to ASTM A1046 SS GR 33
  • Hot Dip Galvanized (HG):  Steel conforms to ASTM A1011 SS GR 33, Finish conforms to ASTM A123
  • Perma-Green (GR):  Steel conforms to ASTM A1011 SS GR 33, E-Coat finish
  • Perma-Gold (ZD):  Steel conforms to ASTM A1011 SS GR 33, Finish conforms to ASTM B633, Type II SC3
  • Plain (PL):  Conforms to ASTM A1011 SS GR 33

Materials & Finishes – Special Metals:

  • Stainless Steel, Type 304 (SS):  ASTM A240, Type 304 *
  • Stainless Steel, Type 316 (ST):  ASTM A240, Type 316 *
  • Aluminum (EA):  ASTM B221, Type 6063-T6 (Extruded) *

* These materials have different physical properties and performance characteristics. Please contact us for design support.

Scroll to Top